DIN-RDS4 is an optical isolator/splitter for DMX512 & RDM networks.  Designed primarily for installation use, the DIN-RDS4 has 4 isolated outputs and one input, all on screw terminals.  It can be powered from a 9V-24V DC plug pack or DIN-rail mount power supply.

The DIN-RDS4 supports one universe (512 channels) of DMX and fully complies with the RDM ANSI E1.20 standard.  

Features:

• 1 input DMX on 3-way screw connector
• 4 output DMX ports on 3-way screw connectors
• Status LED
• DMX activity LED
• RDM activity LED
• standard 4 module wide DIN-rail enclosure (70mm wide x 110mm high (inc. terminals) x 60mm deep)
• Operating 0 >50°C ambient

The DIN-LED4PX is a 4-channel LED driver for constant voltage LED's.  It can accept DMX control or has inbuilt programs accessible via RDM.  DMX address is also set via RDM. 

Features:

• Each channel can control up to 1A @ 24V (supplied by external power supply).
• Dimming is performed with a 500Hz PWM signal, and 8 bit resolution.
• There are 2 automode programs with adjustable speeds that cycle through colours when RGB leds are connected to the outputs.
• DMX address or Automode is set using any standard RDM controller.
• 4 LED ports on 10-way screw connectors
• 1 input DMX on 3-way screw connector
• Status LED
• Each channel has auto reset 1A over current protection
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-LED4 350X is a 4-channel LED driver for constant current LED’s. It can accept DMX control or has inbuilt programs accessible via RDM. DMX address is also set via RDM.

Features:

• Each channel can control up to 7 x 1 watt LED's in series
• Dimming is performed with a 500Hz PWM signal, and 8 bit resolution.
• There are 2 automode programs with adjustable speeds that cycle through colours when RGB leds are connected to the outputs.
• DMX address or Automode is set using any standard RDM controller.
• 4 LED ports on 10-way screw connectors
• 1 input DMX on 3-way screw connector
• Status LED
• Each channel has auto reset 1A over current protection
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-LED4 700X is a 4-channel LED driver for constant current LED's. It can accept DMX control or has inbuilt programs accessible via RDM. DMX address is also set via RDM.

Features:

• Each channel can control up to 7 x 2 watt LED's in series
• Dimming is performed with a 500Hz PWM signal, and 8 bit resolution.
• There are 2 automode programs with adjustable speeds that cycle through colours when RGB leds are connected to the outputs.
• DMX address or Automode is set using any standard RDM controller.
• 4 LED ports on 10-way screw connectors
• 1 input DMX on 3-way screw connector
• Status LED
• Each channel has auto reset 1A over current protection
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-LED4 1000X is a 4-channel LED driver for constant current LED's. It can accept DMX control or has inbuilt programs accessible via RDM. DMX address is also set via RDM.

Features:

• Each channel can control up to 7 x 3 watt LED's in series
• Dimming is performed with a 500Hz PWM signal, and 8 bit resolution.
• There are 2 automode programs with adjustable speeds that cycle through colours when RGB leds are connected to the outputs.
• DMX address or Automode is set using any standard RDM controller.
• 4 LED ports on 10-way screw connectors
• 1 input DMX on 3-way screw connector
• Status LED
• Each channel has auto reset 1A over current protection
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-Input 8 is an 8-way dry contact input to DIN-NET interface.  It can detect a close or open on any of its 8 isolated inputs and send a pre-programmed action to any other device on the DIN-NET network.  

Suggested uses include interfacing between a switch plate or relay contact to the RS232 module, allowing wall-mounted switch plate control of a DMXStreamer or DMXPlayback, for example.

DIN-NET commands are programmed using the free DIN-Tool configuration software.
For further information on DIN-NET see the DIN-TEC User's Manual.

Features:

• 8 isolated contact closure inputs on screw terminals
• 500V isolation
• Trigger on : contact open, contact close or change of state
• In and Thru DIN-NET ports on RJ45 connectors
• Up to 32 DIN-NET actions (1 input can trigger multiple actions)
• Status LED
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-RS232 is RS232 to DIN-NET interface.  It can send RS232 strings when a particular DIN-NET action is received or send pre-programmed DIN-NET actions when it receives a particular RS232 string.  

DIN-NET commands are programmed using the free DIN-Tool configuration software.
For further information on DIN-NET see the DIN-TEC User's Manual.

Features:

• RS232 port (DTE or DCE configurable by jumpers)
• RS232 port adjustable speed from 1200 to 115200 baud
• Output string is 99 characters long max
• Input string matching is 99 characters long max
• In and Thru DIN-NET ports on RJ45 connectors
• Status LED
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-POWER is a power injector for the DIN-NET Network. At least one DIN-POWER is required per DIN-NET Network. 

The DIN-POWER module takes 9V – 24V DC input from an external power supply through a screw terminal or DC jack and injects power onto the DIN-NET through the RJ45 connectors.

Multiple DIN-POWER modules can be used on larger networks.  We recommend the use of quality (CE, UL) power supplies.

For further information on DIN-NET see the DIN-TEC User's Manual.

Features:

• DC jack and screw terminal power inputs
• 9 to 24V DC input
• Polarity protected
• Status LED
• Standard 4 module wide DIN-rail enclosure
• Operating 0 >50°C ambient

The DIN-NET USB is a USB to DIN-NET interface.  It allows the free DIN-Tool software to talk to the DIN-NET devices on your network via your PC's USB port.

DIN-TOOL software discovers available devices and allows you to link DIN-NET actions or RS232 strings to switch closures on a DIN-INPUT8, for example.   

For further information on DIN-NET see the DIN-TEC User's Manual.

Features:

• Configure DIN-TEC interfaces from your PC
• Custom options for each interface
• Discover how many interfaces currently on the network
• User defined Commands & Action for each destination (RS232)
• Manage each interface in the same software
• Import / Export saved configurations for each interface